Instructions for Use
How to Use the Products
Some treatments using TEC 2000 products can be performed by yourself, while others should be entrusted to a mechanic, such as during periodic oil changes. Choose a product from the list and see the usage instructions:
TEC 2000 Engine Flush
Engine Flush - Oil System
How to Use
TEC 2000 Engine Flush
Key Information
TEC 2000 Engine Flush should be used during a standard oil change.
- Add the product to the engine, still with the old oil. The engine should reach its normal operating temperature.
- After adding the product, let the engine idle for about 10-15 minutes (ensure the car is in a well-ventilated area or outside to avoid exhaust fume poisoning).
- After this time, drain the old oil, install a new filter, and refill with new oil.
If the engine has problems such as sticky rings, uneven compression, increased oil consumption, or black smoke, the treatment should last about 25-30 minutes before changing the oil.
The unique combination of highly effective detergents and very efficient lubrication allows the product to be used in all combustion engines – gasoline, diesel, and gas-powered. The operation is completely safe for the engine.
375ml
For 4-5 Liters of Oil
Manual
Warm up the engine
Heat the engine until the coolant temperature reaches ~60︒C.
Turn off the engine
Remove the oil filler cap and pour the product into the engine
Use 1 can (375 ml) for 4-5 liters of engine oil.
Replace the oil filler cap
Start the engine and let it idle for ~15 minutes
Note 1: Keep the car on private property or in a well-ventilated area. Note 2: If there is a suspicion of a large amount of deposits in the engine, if the engine exhibits increased smoking, or if it consumes more than 1 liter of oil per 1000 km, the flushing process can be extended.
Turn off the engine, remove the oil filter, and drain the used oil along with the flush
Install a new oil filter and fill the engine with oil to the appropriate level
Start the engine for about 30 seconds, turn it off, then check the oil level and top it up to the correct level
TEC 2000 Diesel System Cleaner
Fuel System and Injector Cleaning for Diesel
How to Use
TEC 2000 Diesel System Cleaner
Key Information
The Diesel Fuel Additive TEC 2000 Diesel System Cleaner is poured directly into the fuel tank.
Have you used competitive products before? If so, it is advisable to replace the fuel filter before adding TEC 2000 Diesel System Cleaner.
To extend the reliability of injectors, we recommend using it twice a year – in autumn and summer.
The vehicle can operate on the pure, undiluted product.
375ml
Suitable for approximately 40 liters of fuel.
Manual
Pour the product into the fuel tank
If there is a suspicion of contaminants in the tank (e.g., water or paraffin), use 1 can (375 ml) for approximately 25 liters of fuel.
Fill the tank to full
Burn through the fuel with the additive
After using the product, it is recommended to replace the fuel filter.
TEC 2000 Fuel System Cleaner
Fuel System and Injector Cleaning for Gasoline
How to Use
TEC 2000 Fuel System Cleaner
Key Information
TEC 2000 Fuel System Cleaner is used for all gasoline engines and is safe for catalytic converters.
TEC 2000 Fuel System Cleaner is used by pouring the contents of the can into the fuel tank.
It is recommended that the tank be full.
Repeat the operation twice a year, preferably at the turn of winter and spring, and in late autumn. This is recommended because these periods experience the greatest temperature fluctuations, causing water to condense in fuel tanks.
The vehicle can operate on the pure, undiluted product.
375ml
Suitable for 40 liters of fuel.
Manual
Pour the product into the fuel tank
If there is a suspicion of contaminants in the tank (e.g., water or paraffin), use 1 can (375 ml) for approximately 25 liters of fuel.
Burn through the fuel with the additive
Fill the tank to full
After using the product, it is recommended to replace the fuel filter.
TEC 2000 Diesel Injector Cleaner
Direct Cleaning of Diesel Injectors
How to Use
TEC 2000 Diesel Injector Cleaner
Key Information
TEC 2000 Diesel Injector Cleaner is used to reduce exhaust smoke and is best administered directly to the injector rail. This can be done using a universal injector cleaning device offered by various companies in the market. The procedure takes approximately 20 minutes.
Note:
- Do not use on a hot engine as this may cause the product to boil.
- If the engine's cooling system may be malfunctioning, apply with breaks.
- Use with the engine hood open.
The benefits of using the product will be immediately noticeable. The engine will run smoothly, and the exhaust emissions will be visibly cleaner. To keep injectors clean and highly efficient, perform the above procedure once or twice a year.
375ml
Suitable for about 20 minutes of operation.
Manual
Disconnect the fuel supply and return lines from the rail
Attach the service lines from the injector cleaning machine in place of the factory lines, and place the free ends into the can of TEC 2000 Diesel Injector Cleaner
Start the engine, allowing it to run on TEC 2000 DIC. One can (375 ml) is sufficient for about 20 minutes of operation.
When the can is empty, turn off the engine
Disconnect the service lines
Reconnect the factory lines
Note 1: If the effect is partial or the injectors were particularly dirty, it is recommended to repeat the entire procedure. Note 2: If the above method is not possible, insert the end of the vehicle's fuel pump suction pipe into the can of TEC 2000 Diesel Injector Cleaner. Ensure the "return to tank" pipe is also inserted into the can. Run the engine until the can is nearly empty. For better results in high-mileage engines, extend the procedure by another 20 minutes using an additional 375 ml can of TEC 2000 Diesel Injector Cleaner.
Run the engine at idle for approximately 20 minutes
TEC 2000 Fuel Injector Cleaner
Direct Cleaning of Gasoline Injectors
How to Use
TEC 2000 Fuel Injector Cleaner
Key Information
The best solution is to apply the product directly to the injector rail using a universal injector cleaning device, which can be easily found on the market.
Such a device usually consists of two hoses with a diameter of about 8 mm and a length of about 1.5 meters.
We recommend installing a fuel filter on the cleaning system (between the can and the injector rail).
Injector cleaning is completed when the product in the can is depleted.
Note:
- In case of suspected malfunction of the cooling system, apply the product with breaks.
- The gasoline injector cleaner should be used with the engine hood open.
If the injectors in your vehicle are heavily contaminated, it is recommended that the application of the product lasts a bit longer (approximately 40 minutes), using two cans of TEC 2000 Fuel Injector Cleaner (2×375 ml).
375ml
Suitable for approximately 20 minutes of operation.
Manual
Disconnect the fuel supply and return lines from the injector rail
Attach the service lines (in place of the factory lines) to a universal injector cleaning device
Insert the ends of the service lines into the can of TEC 2000 Fuel Injector Cleaner
Start the engine
From this point, the product starts working. One can (375 ml) is sufficient for about 20 minutes of operation.
When the can is empty, turn off the engine
Disconnect the service lines
Reconnect the factory lines
Note: After the procedure, it is recommended to replace the fuel filter.
TEC 2000 Oil Booster
Oil Additive
How to Use
TEC 2000 Oil Booster
Key Information
The product is designed for all gasoline and diesel engines.
To fully utilize the properties of the Oil Booster, it is best to use TEC 2000 Engine Flush before adding the product.
TEC 2000 Oil Booster is added to the oil during a routine oil change or immediately after changing to fresh oil.
It is beneficial if the engine has already been started previously. Before adding the additive, the engine should be warmed up to operating temperature.
375ml
Suitable for every full 4 liters of engine oil.
Manual
Pour the Oil Booster into the engine when the engine is off.
The application is the same as for regular engine oil.
Start the engine and let it idle for about 5 minutes.
Note: For best results, use oils with specifications of 5W / 10W / 20W – 50. API "SH" type oils or better.
TEC 2000 Induction Cleaner
Intake System Cleaner
How to Use
TEC 2000 Induction Cleaner
Key Information
While cleaning the intake, remember that TEC 2000 Induction Cleaner:
- Is highly flammable
- Contains rich lubricating additives
- Has strong corrosive properties; therefore, be careful during application to avoid contact with the car body or lights.
Do not use the product too frequently as it affects engine RPM, which should be around 2-2.5 thousand RPM. Therefore, proper application of TEC 2000 Induction Cleaner requires two people: one to apply the cleaner and another to control the engine RPM.
TEC 2000 Induction Cleaner can be used in all engines, particularly recommended for diesel engines and gasoline engines with direct fuel injection.
Regular use of TEC 2000 Induction Cleaner will reduce maintenance costs, repairs, and cleaning of components sensitive to contamination. Using the product does not require specialized mechanical knowledge, making it suitable for home use as well.
Manual
Remove the intake pipe after the air filter
Start the engine
Apply a small amount of the product into the intake system in 2-3 second intervals.
If you want a thorough cleaning of the intake, apply the product for about 20 minutes.
Turn off the engine and reassemble the intake system.
TEC 2000 Radiator Flush
Radiator Cleaning Fluid
How to Use
TEC 2000 Radiator Flush
Key Information
TEC 2000 Radiator Flush is very easy to use.
What should you remember when using the cooling system flush?
REMEMBER THAT THE FLUID IN THE COOLING SYSTEM IS VERY HOT AND UNDER CONSTANT PRESSURE. UNSCREWING THE FILLER CAP TOO QUICKLY CAN RESULT IN SKIN BURNS. THEREFORE, MAKE SURE TO PERFORM THE ENTIRE OPERATION SLOWLY, WITH MODERATE UNSCREWING SPEED. FOR GREATER PROTECTION, WE RECOMMEND WEARING PROTECTIVE CLOTHING, INCLUDING GLOVES AND SAFETY GOGGLES.
325ml
Suitable for 10-15 liters of coolant.
Manual
Remove the coolant cap from the expansion tank and pour the product into the tank, then replace the cap.
Start the engine and heat it until the radiator fan turns on.
Turn on the heating in the car cabin to the maximum temperature.
Let the engine idle for 15 minutes.
Turn off the engine, wait a while for the engine to cool down, then carefully and slowly remove the expansion tank cap, and drain the coolant with the additive, following safety precautions and waste storage requirements.
Fill the cooling system with demineralized water.
Start the engine and let it idle for 5 minutes.
Drain the demineralized water, following safety and personal protection measures.
Fill the cooling system with coolant and replace the expansion tank cap.
Bleed the cooling system.
TEC 2000 Radiator Stop Leak
Radiator Sealant
How to Use
TEC 2000 Radiator Stop Leak
Key Information
While cleaning the intake, remember that TEC 2000 Induction Cleaner:
- Is highly flammable
- Contains rich lubricating additives
- Has strong corrosive properties; therefore, be careful during application to avoid contact with the car body or lights.
Do not use the product too frequently as it affects engine RPM, which should be around 2-2.5 thousand RPM. Therefore, proper application of TEC 2000 Induction Cleaner requires two people: one to apply the cleaner and another to control the engine RPM.
TEC 2000 Induction Cleaner can be used in all engines, particularly recommended for diesel engines and gasoline engines with direct fuel injection.
Regular use of TEC 2000 Induction Cleaner will reduce maintenance costs, repairs, and cleaning of components sensitive to contamination. Using the product does not require specialized mechanical knowledge, making it suitable for home use as well.
325ml
Suitable for 10-15 liters of coolant.
Manual
Shake the container vigorously, then pour the product into the cooling system.
Remember, the engine must be cold!
Start the car and let the engine idle for 20 minutes.
TEC 2000 Airco Fresher Service Spray
Air Conditioning Disinfectant
How to Use
TEC 2000 Airco Freshener Spray
Key Information
TEC 2000 Radiator Flush is very easy to use.
What should you remember when using the cooling system flush?
REMEMBER THAT THE FLUID IN THE COOLING SYSTEM IS VERY HOT AND UNDER CONSTANT PRESSURE. UNSCREWING THE FILLER CAP TOO QUICKLY CAN RESULT IN SKIN BURNS. THEREFORE, MAKE SURE TO PERFORM THE ENTIRE OPERATION SLOWLY, WITH MODERATE UNSCREWING SPEED. FOR GREATER PROTECTION, WE RECOMMEND WEARING PROTECTIVE CLOTHING, INCLUDING GLOVES AND SAFETY GOGGLES.
150ml
Suitable for the interior of an average 5-person mid-sized car.
Manual
Start the engine.
Turn on the air conditioning to the minimum temperature.
Set the internal cabin blower to maximum output.
Activate air recirculation within the cabin.
Shake the can vigorously for at least 30 seconds.
Unlock the spray mechanism and place the can inside the cabin.
Position the can on the floor, preferably on a rubber mat.
Close all doors and windows of the car.
Ensure no people or animals are inside the cabin during spraying as the high concentration of the product can cause suffocation and poisoning.
Wait until the spray has finished dispersing, then wait an additional 5 minutes.
Open the doors, turn off the engine, air conditioning, blower, and air recirculation.
Leave the car with open windows in a well-ventilated area or outdoors for at least 1 hour.