How to use the products
Some of the treatments with TEC 2000 products you are able to perform yourself, have others performed by a mechanic, such as at periodic oil changes.
Choose a product from the list and see the instructions for use:
TEC 2000 Engine Flush
Engine flush - oil system
TEC 2000 Engine Flush
How to use
TEC 2000 Engine Flush should be used during a standard oil change.
Add the product to the engine, still in the old oil. The engine should reach normal operating temperature. After adding the product, the engine should idle for about 10-15 minutes (the car should be in a ventilated room or outside to avoid exhaust gas poisoning). After this time, drain the old oil, install a new filter and top up with new oil.
In case the engine has developed problems such as sticky rings, uneven compression, increased oil consumption or black smoke, work with the preparation should last about 25-30 minutes before changing the oil.
The unique combination of highly effective detergents together with highly effective lubrication allows the product to be used in all internal combustion engines - gasoline, diesel and gas-powered. The operation is completely safe for the engine.
to reach a coolant temperature of ~60︒C
1 can 375 ml for 4-5 liters of motor oil
Note 1: Leave the car on private property, or in a well-ventilated room. Note 2: If you suspect that there is a large amount of carbon build-up in the engine, the engine manifests increased smoke, uses more than 1 liter of oil per 1000km, the flushing process can be extended.
TEC 2000 Diesel System Cleaner
Diesel fuel system and injector cleaning
TEC 2000 Diesel System Cleaner
How to use
Diesel TEC 2000 Diesel System Cleaner is poured directly into the fuel tank.
Have you used competitive products before? If so, we recommend replacing the fuel filter before pouring TEC 2000 Diesel System Cleaner.
To prolong the reliability of the injectors, we recommend using twice a year - in autumn and summer.
The vehicle can run on clean, undiluted product.
If you suspect that there are impurities in the tank (such as water or paraffin), you can use 1 can (375ml) ~25 liters of fuel.
After applying the product, we recommend replacing the fuel filter.
TEC 2000 Fuel System Cleaner
Cleaning the fuel system and injectors Gasoline
TEC 2000 Fuel System Cleaner
How to use
TEC 2000 Fuel System Cleaner applies to all gasoline engines and is safe for catalytic converters.
TEC 2000 Fuel System Cleaner gasoline refiner is applied by pouring the contents of the can into the fuel tank.
It is recommended that the tank be full.
The operation should be repeated twice a year, preferably applied at the turn of winter and spring, and in late autumn, this is recommended because at that time there are the greatest temperature fluctuations and water condenses in the fuel tanks.
The vehicle can run on clean, undiluted product.
If you suspect that there are impurities in the tank (such as water or paraffin), you can use 1 can (375ml) ~25 liters of fuel.
After applying the product, we recommend replacing the fuel filter.
TEC 2000 Diesel Injector Cleaner
Direct cleaning of Diesel injectors
TEC 2000 Diesel Injector Cleaner
How to use
TEC 2000 Diesel Injector Cleaner used to reduce smoke in the exhaust, is best administered directly to the injector rail. For this you can use a universal injector cleaner offered by a number of companies on the market. The procedure takes about 20 minutes.
Caution:
Do not use on a hot engine, it can lead to boiling of the preparation.
If there is a chance that the engine cooling system is not working, apply intermittently.
Apply with the engine hatch open.
The benefits of the product will be immediately noticeable. Engine operation will be even, exhaust gases will be visibly cleaner. To keep the injectors clean and highly efficient, the above should be carried out once or twice a year.
Note 1: However, if the effect is partial or the injectors were particularly heavily contaminated, it is recommended to repeat the entire operation.
Note 2: If none of the above options is inapplicable, insert the end of the suction pipe from the vehicle's fuel pump into the TEC 2000 Diesel Injector Cleaner can, at the same time, the “return to tank” pipe should also be inserted into the can. The engine should run until the contents of the can are almost emptied. Wanting to get better results in high mileage engines, we recommend extending the procedure for another 20 minutes, using an additional 375 ml can of TEC 2000 Diesel Injection Cleaner.
TEC 2000 Fuel Injector Cleaner
Direct injection cleaning Gasoline
TEC 2000 Fuel Injector Cleaner
How to use
The best solution is to apply the product directly to the injector strip using a universal injector cleaning apparatus, which you can easily find on the market.
As a rule, such an apparatus consists of two wires with a diameter of about 8 mm and a length of about 1.5 m.
We recommend that you install a fuel filter on the cleaning apparatus (between the can and the injection rail).
Cleaning of the injectors ends when the preparation in the can is exhausted.
Attention:
- in case of suspected cooling system malfunction, the preparation should be applied intermittently,
- gasoline injector cleaner should be applied with the engine hatch open.
If the injectors in your vehicle are heavily contaminated, we recommend that the application of the product take a little longer (about 40 minutes), using two cans of TEC 2000 Fuel Injector Cleaner (2×375 ml).
From this point the preparation begins to work. One can, i.e. 375 ml, is sufficient for about 20 minutes of work
Note: after the entire procedure, we recommend replacing the fuel filter.
TEC 2000 Oil Booster
Oil additive
TEC 2000 Oil BOOSTER
How to use
The formulation is dedicated to all gasoline and diesel engines.
To take full advantage of Oil Booster's properties, it is best to use TEC 2000 Engine Flush before adding the product
TEC 2000 Oil Booster is added to the oil during a routine mixture change or immediately after an oil change, to fresh oil.
It is good if the engine has already been started. The engine should be warmed up to operating temperature before adding the additive.
The application is the same as for regular motor oil
Attention:
If you want to get the best results, bet on oils with specifications of 5W / 10W / 20W - 50. API type oils “SH” or better
TEC 2000 Induction Cleaner
Preparation for cleaning the intake system
TEC 2000 Induction Cleaner
How to use
When cleaning the intake, remember that TEC 2000 Induction Cleaner: is extremely flammable, is rich in lubricating additives, and has a highly corrosive effect; hence, be careful of the body or lights during application.
Do not use the product too often, as it affects the engine's RPM. These, in turn, should be about 2-2.5 thousand/rpm. Therefore, for proper application of TEC 2000 Induction Cleaner, two people are needed: one to administer the product, the other to control the revolutions.
TEC 2000 Induction Cleaner can be used in all engines. It is especially recommended for diesel engines and gasoline engines with direct fuel injection.
Regular use of TEC 2000 Induction Cleaner will reduce the cost of operation, repair, and cleaning of contamination-sensitive components. Use of the agent in most cases does not require mechanical expertise, making it also recommended for home use.
However, it is recommended to consult a mechanic or check the vehicle manufacturer's recommendations before use in specific types of engines, especially those with non-standard designs or with unusual intake systems.
If you want to thoroughly clean the intake, give the preparation pt.rz for about 20 minutes.
TEC 2000 Radiator Flush
Radiator cleaner
TEC 2000 Radiator Flush
How to use
TEC 2000 Radiator Flush is very easy to use.
What do you need to keep in mind when using the cooling system flush agent?
FIRST OF ALL, THAT THE FLUID IN THE COOLING SYSTEM IS VERY HOT AND UNDER CONSTANT PRESSURE. UNSCREWING THE FILLER CAP TOO QUICKLY CAN RESULT IN SKIN BURNS. THEREFORE, REMEMBER TO CARRY OUT THE ENTIRE OPERATION SLOWLY, WITH A MODERATE UNSCREWING RATE. FOR GREATER PROTECTION, WE RECOMMEND WEARING PROTECTIVE CLOTHING, INCLUDING: GLOVES AND SAFETY GLASSES.
TEC 2000 Radiator Stop Leak
Radiator seal
TEC 2000 Radiator Stop Leak
How to use
TEC 2000 Radiator Stop Leak seal fluid is best used prophylactically (it does not reduce coolant flow). With prophylactic use, the fluid will protect the engine from overheating when the leaks are no larger than 1.5 mm and protect against coolant aging
Sealing the radiator - remember this
When using radiator sealant, you need to remember a couple of things. First and foremost, to TAKE SPECIAL CAUTION WHEN you unscrew the filler. WHY. KEEP IN MIND THAT THE COOLANT IS PRESSURIZED AND ITS TEMPERATURE IS SO HIGH THAT IT IS VERY EASY TO GET BURNED.
SO HOW TO USE RADIATOR SEALANT SO AS NOT TO ENDANGER YOUR HEALTH? WE RECOMMEND WEARING PROTECTIVE CLOTHING, INCLUDING GLOVES AND GOGGLES, AND SLOWLY UNSCREWING THE CAP.
Remember that the engine must be cold!
TEC 2000 Airco Fresher Service Spray
Degreaser for air conditioning
TEC 2000 Airco Freshener Spray
How to use
When spraying the product, there must be no people or animals in the cabin - the product in high concentration can cause shortness of breath and poisoning.
